| Technical Specification |
| Conformity to specification IS 6893 part 2 |
Yes |
| Milling Arbor as per IS 8614 latest |
Yes |
| Mechanical Guarding as per IS 9474 latest |
Yes |
| Geometrical and Practical Accuracy as per IS 2200 latest |
Yes |
| Geometrical Accuracy test for inspection of the machine conforming to IS: 2201 - 1973 |
Yes |
| Machine standard As per IS: 210-1993 |
Yes |
| Mechanism |
Manually Operated |
| Table Total Area (Length x Width) (mm x mm) |
1200 x 300 |
| Table Clamping Area (Length x Width ) , mm x mm |
1270X254 |
| Width of T slots in mm |
16 millimeter |
| Number of T Slots |
3 |
| Centre Distance between T slots in mm |
52 Millimeter |
| Table Transverse |
Manual & Automatic |
| Longitudinal Table Transverse in mm |
89 millimeter |
| Cross Table Transverse in mm |
406 millimeter |
| Vertical Transverse in mm |
406 millimeter |
| Swivel of Milling Head to either side in vertical plane |
45 |
| for vertical milling in degree |
|
| Maximum Safe Load on table in KG |
300 kilogram |
| Number of Spindle Speed |
16 |
| Spindle Speed range in rev/min |
66 TO 4540 RPM |
| Spindle Front Bearing Diameter in mm |
89 millimeter |
| Type and Size of Spindle Nose |
ISO30/R8 |
| Vertical Movement of Quill in mm |
127 |
| Vertical Quill Diameter in mm |
86 millimeter |
| ISO Compliance for Milling Machine |
ISO 30 |
| Size of Milling Arbor |
As per ISO 30 |
| Power Supply (V, Ph , Hz) |
3Ph |
| Spindle Motor Power in Kw |
2.23 kilowatt |
| Spindle Motor RPM |
4540 |
| Thermal Safety Over Load Relay |
Yes |
| Control circuit switching off during Voltage drop |
Yes |
| Single phase preventer |
Yes |
| Positive clamping of all guide ways thru clamping pads |
Yes |
| Streamlined construction, rigged and vibration free |
Yes |
| Power operated Feeds and Rapid traverse in all axis |
Yes |
| Independent main drive and feed drive |
Yes |
| Inch push button for speed & feed drives |
Yes |
| Automatic Lubrication to all slide |
Yes |
| Thermal Stability of bearing over excess temperature above 40 |
Yes |
| degree cel |
|
| Electric equipment |
Yes |
| Machine casting of Column/Knee/Saddle/Table confirms to Cast Iron Grade FG-260 & Hardness 180-230 BHN |
Yes |
| Main Spindle of C2R grade forged Steel and hardened 58-62 HRC |
Yes |
| Drive gears of Alloy steel material specification 15Ni 7 Cr 4 M02 |
Yes |
| Pre-loaded Standard make High precision class P3 set of taper roller bearings for main spindle |
Yes |
| Draw Bolt with draw nut |
Yes |
| Elevating crank handle |
Yes |
| Over arm brace for vertical / horizontal & Universal milling |
Yes |
| Machine Lamp |
Yes |
| Service Tool kit for operation & maintenance |
Yes |
| Operation & Maintenance Manual |
Yes |
| Foundation bolts & levelling plate |
Yes |
| ACCESSORIES-QTY.: 1 NO. EACH |
| Machine vice with swivel base 200mm |
| Self-Centering vice 10-80 mm |
| Stub Milling Arbor dia 16,22,27,32 & 40 mm |
| Collet Holder with set of conical collets size5,6,8,10,12 &20 mm |
| End mill holders dia 5,6,8,10,16&20 mm |
| Reduction sleeve type B size MT1,MT2,MT3&MT4 |
| Vertical Milling head |
| 3 Axis DRO |
