| TECHNICAL SPECIFICATION |
| Model |
SI-TWM-300 |
| Mains connection voltage |
3ph, 50/60 Hz 380...460 V ±10 % |
| Maximum supply current |
12...16 A |
| Fuse |
16 A |
| Open circuit voltage (average) |
MMA, 50 V |
| Rated maximum output at 40 °C |
40 % TIG, 300 A / 22 V |
| Range of output |
TIG 3 A / 1 V ... 300 A / 38 V |
| MMA 10 A / 10 V ... 250 A / 39 V |
| Power factor, λ |
400 V, MMA 250 A /30V, 0.9 |
| Efficiency, ƞ |
400 V, MMA 190A/27.6V, 85% |
| Idle power |
TIG 20 W |
| Operating temperature range |
-20...+45 °C |
| Storage temperature range |
-20...+60 °C |
| EMC class |
A |
| Degree of protection |
IP23S |
| Voltage supply for cooling unit Ucu |
380...460 V |
| Recommended generator power (MIN) |
Sgen, 20 kVA |
| Wireless communication type for remote |
Transmitter Frequency and power, 2.4 GHz Bluetooth, 2400-2483.5 MHz, 10 dBm |
| Wired communication type |
Remote, Analog |
| CAN BUS |
Can Bus |
| Stick electrode diameters |
ø mm 1.6…4.0 mm |
| Standards |
IEC60974-1,-3,-10 |
| IEC 61000-3-12 |
| AS 60974.1-2006 (3 GB 15579.1 |
| Functions TIG: |
TIG HF Start, TIG LIFT Start & TIG Spot available |
| Pre Flow |
0 to 10 Sec |
| Start Current Adjustment |
5 - 300% |
| Up Slope |
adjustable 0-5 Secs (Steps of 0.1sec); |
| Down Slope |
0.1 – 15 sec. |
| Post Flow |
0 to 30 sec |
| Hot Start level |
- 80% to + 100% |
| Hot Start time |
0.1 sec to 9.9 sec |
| TIG Pulse Frequency |
0.2 Hz to 300 Hz |
| Double Pulse Feature |
Yes |
| 2/4 stroke |
Yes |
| Memories |
90 memory |
| Current mode |
DC-/ DC+ / AC/ MIX |
| AC Waveform |
Sine /Optima/Square |
| AC Frequency |
30 Hz ... 250 Hz |
| AC+ / AC- balance |
-60 %...0 % |
| MIX TIG AC (time) ratio |
10 %...90 %,step 1 % |
| MIX TIG cycle time |
0.1s... 1.0s, step 0.1 s |
| MMA settings: |
|
| Hot start |
-10 ... +10, step 1 (Default = 0) |
| Arc force |
-10 ... +10, step 1 (Default = 0) |
| MMA antifreeze OFF / ON (Default = OFF) |
Yes |
| VRD mode OFF / ON (Default = OFF) |
Yes |
| Cooling Unit minimum specifications |
|
| Connection voltage |
220...460 V AC, 1~/3~ |
| Maximum rated supply current |
1.0 A |
| Rated cooling power at 1 l/min |
0.9 kW |
| Cooling power at 1.6 l/min |
1.0 kW |
| Recommended coolant |
MPG 4456 |
| Coolant pressure |
0.4 MPa |
| Tank volume |
3.0 1 |
| Operating temperature range * |
-20 ... +45 °C |
| Storage temperature range |
-20 ... +60 °C |
| EMC class |
A |
| Degree of protection ** |
IP23S |
| Standards |
IEC 60974-2 |
| IEC 60974-10 |
| Features : |
|
| A) Power Source: |
| •Error code display for maintenance purpose. |
| • Auto cut off built in the power source. Over heat, under voltage, phase absence protections, phase failure indicator provided . Suitable indication/alarm on the above failure |
| •Protection circuit. |
| •provided infinitely variable stepless current controls. |
| •support both TIG and MMA welding with AC/DC output with control feature and frequency control. |
| • Pre-set waveform control in AC welding, Sine, square and optima wave form. |
| • Capable of micro tacking function controller. |
| • Capability to change the welding current during welding without extinguishing of the arc. |
| • Function to set the search arc and tail arc while performing. |
| • Machine Compatible with Water Cooling unit |
| B) Display must be compatible with following selection |
| • Compatible with selection of material about to weld Fe / SS /AL |
| • Compatible with Selection of Welded material. |
| • Compatible with selection of Joint. |
| • Compatible with selection of Joint Position. |
| • Compatible with Water Cooling unit |
